4
Figure 3
Heat function On or press the Purire™ On/Off button
to turn the Purire™ function ON.
FrequencyInterference
If the replace does not respond properly to the remote
control, the remote operating frequency may have to be
reset. The remote control can send another frequency code
to the circuit board to eliminate
interference.
1. Simultaneously press the “SlowStart” button and the
“Purire™LowSpeed” button on the remote control.
2. “CODE” will appear.
3. Release the “SlowStart” button and the “Purire™Low
Speed” button.
4. Press and hold the initialization button on the unit.
5. Press the
button on the remote and release the
initialization button.
Your remote will now have a different frequency
communicating with the replace.
RemoteControlFunctions(Figure 3)
1. RoomTemperature
2. SetTemperature*
3. Dimmer
4. FlameSpeedControl
5. SlowStart/Fading
EmbersControl
6. Purier™Speed
7. TemperatureDown*
8. TemperatureUp*
9. DimmerDown/
FirelightOff
2. SetTemperature*
1. Press 17.FlameHeatOn/Off button to turn replace on.
2. Press 8.TemperatureUp to raise thermostat.
3. Press 7.TemperatureDown to lower thermostat.
4. Press both 8.TemperatureUp and 7.Temperature
Down to change °F to °C.
!
*NOTE: The set temperature buttons are not operational
on the DF3215NH model replaces.
3. LightDimmer
Firelight
1. Press the 17.Flame/HeatOn/Off button to turn the
Flame/Heat On.
2. Repeatedly press the 10.LightDimmerUp or 9.Light
DimmerDown button to decrease or increase the
brightness of the upper lights.
3. To activate the “Firelight”, continue pressing 10.Light
DimmerUp until the “FirelightOn” icon
is shown on
the display screen.
4. To shut the “Firelight” off, turn the 9.LightDimmer
Down button until the “Firelight” icon off
is shown on
the display.
4. FlameSpeed
1. Press the 17.Flame/HeatOn/Off button to turn the
Flame/Heat On.
2. Press the 12.FlameSpeedUp to increase the speed of
the ame.
3. Press the 11.FlameSpeedDown to decrease the speed
of the ame.
5. SlowStart/FadingEmbers
The slow start function simulates a starting re. The slow
start function is automatically programmed for 30 seconds.
The slow start timer setting cannot be changed. The fading
embers function simulates a re going out. The fading
embers timer can be set to 1, 5 or 10 minutes.
1. Press the 14.SlowStartFadingEmbers On button to
turn the Slow Start/Fading Embers function on.
2. Press the 14.FadingEmbers On button repeatedly to
set the fading embers timer time to 1, 5 or 10 minutes.
3. Press the 13.FadingEmbersOff button to turn the
Fading Embers timer function off.
6. Purier™Speed
Press the 18.Purire™On/Off button to turn the Purire™
function On. When the Purire™ function is On the
Purire™ Speed symbol will ash. When off the symbol
will be solid. The default setting for the Purire™ is set at
low speed. Press the 16.Purier™HighSpeedbutton
to switch to the high speed level and the Purier™Speed
symbol will ash more quickly. Press the 15.Purier™Low
Speedbutton to switch back to the lower speed, or Press the
18.Purire™On/Off button to turn the Purire™ function
Off.
10. DimmerUp/Firelight
On
11. FlameSpeedDown
12. FlameSpeedUp
13. SlowStart/Fading
EmbersOff
14. FadingEmbersOn/
TimerCycle
15. Purier™LowSpeed
16. Purier™HighSpeed
17. Flame&HeatOn/Off
18. Purier™On/Off
11
10
12
9
2
5
1
4
7
3
1413
8
6
1615
1817
Comments to this Manuals