CEMOUNTING and OPERATING MANUALReversible Air-to-Water Heat Pumpfor Outdoor InstallationLA 16ASROrder No.: 452158.66.21 FD 8507
10APPENDIX11.1 DIMENSION DRAWING 1111.2 EQUIPMENT DATA 1211.3 SCHEMATICS11.3.1 Heating Mode 1311.3.2 Cooling Mode 1411.4 WIRING DIAGRAMS11.4.1 Control
11Dimension DrawingAPPENDIX: 11.1 DIMENSION DRAWING
12Equipment DataAPPENDIX: 11.2 EQUIPMENT DATA
1311.3.1 Heating ModeAPPENDIX: 11.3 SCHEMATICS
1411.3.2 Cooling ModeAPPENDIX: 11.3 SCHEMATICS
1511.4.1 ControlAPPENDIX: 11.4 WIRING DIAGRAMSCable diameters all 0,75mm2Control lead 20x1,0mm2Heat pump controller
1611.4.2 LoadAPPENDIX: 11.4 WIRING DIAGRAMSPEdistributorMainsCable diameters all 0,75mm2ye/gnye/gn
1711.4.3 Terminal DiagramAPPENDIX: 11.4 WIRING DIAGRAMSTerminal connection diagram and connector assignmentin the reversible air-to-water outdoor unit
18E1 Crankcase heater, compressorE2 Fan for nozzle ring heaterE3 Defrost end pressostatE4 Condensing pressure pressostatF2 High-pressure pressostatF3
19Hydraulic Block DiagramAPPENDIX: 11.5 HYDRAULIC BLOCK DIAGRAMN1-N05(HUP)N1-N06(WUP)N2-N02(SUP)N1-N010EVN1-B3(WWF)KWTWWEVN2-N01(HUPR)N1-B6(NKF)N1-N04
21 READ IMMEDIATELY 31.1 Important Information1.2 Legal Provisions and Guidelines1.3 Energy-Efficient Use of Heat Pumps2 PURPOSE OF HEAT PUMP 42.1 App
20EC Declaration of ConformityAPPENDIX: 11.6 EC DECLARATION OF CONFORMITYDeclaration of ConformityThe undersignedKKW Kulmbacher Klimageräte-Werk GmbH,
Notes21
Notes22
Notes23
KKW Kulmbacher Klimageräte-Werk GmbH Technical data subject to change without noticeGeschäftsbereich Dimplex Fax +49 (0) 92 21 709-589Am Goldenen Feld
3READ IMMEDIATELY1.1 Important InformationPrior to opening the unit it must beensured that all electrical circuits are disconnectedfrom the power sour
4valve as well as the low-noise compressor, adesuperheater, a condenser and the electric controlunit.In the case of low ambient temperatures, air hum
52.2.1.1.1.3.1.1.3.2.SCOPE OF DELIVERYTRANSPORT4CAUTION!3.2 Control BoxThe control box is integrated in the heat pump. It canbe folded downward after
6INSTALLATIONMOUNTING6INSTALLATION5.1 GeneralThe unit should always be installed on a permanentlylevel, smooth and horizontal floor. The entire basefr
7MOUNTINGCOMMISSIONING6.3 Electrical ConnectionThe power connection of the heat pump is effectedvia a commercially available 4-core cable.The cable ha
8COMMISSIONINGCLEANING / MAINTENANCEf) Once all heating circuit are fully open and aheating water temperature of approx. 25 °C ismaintained in the buf
9CLEANING / MAINTENANCEMALFUNCTIONS / TROUBLESHOOTINGDECOMMISSIONINGthe supply and return line of the heat pump. Theregulations of the trade associati
Comments to this Manuals