Dimplex DF2624L Service Manual download pdf (Page 8)

8 www.dimplex.com

AC/DC ADAPTER REPLACEMENT

Tools Required: Phillips Head Screwdriver

Flat Head Screwdriver

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the three screws along the back of the unit,

the two on either side along the top edge and the two

at the top of the glass retaining bracket on both sides.

(Figure 3)

4. Lay the Compact Fireplace on its back.

5. Gently open the top panel, laying it on the work sur-

face so that all of the components can easily be seen.

(Figure 4)

6. Locate the adapter and disconnect the wiring connec-

tions noting their original locations.

7. There is one connection located on the display/control

board that requires the board to be removed. This can

be done by removing the two screws on the right hand

side of the unit, reaching between the partially reective

panel and the back of the unit, to remove the display/

control board to remove the connection and replace it

with the new one.

8. Reinstall the display/control board.

9. Remove the adapter from the top panel by removing

the four screws securing it to the top panel.

10. Properly orient and insert the new adapter and connect

all of the wiring.

11. Reassemble in the reverse order as above.

DISPLAY/CONTROL BOARD

REPLACEMENT

Tools Required: Phillips Head Screwdriver

Flat Head Screwdriver

Needle Nose Pliers

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the three screws along the back of the unit,

the two on either side along the top edge and the two

at the top of the glass retaining bracket on both sides.

(Figure 3)

4. Lay the Compact Fireplace on its back.

5. Gently open the top panel, laying it on the work sur-

face so that all of the components can easily be seen.

(Figure 4)

6. Locate the display/control board behind the partially

reective panel and remove the two screws that attach

it to the unit.

7. Disconnect the wiring connections noting their original

locations.

8. Release the display/control board from the support

panel by using needle nose pliers to depress the tab on

the mounting standoffs and gently lift the board off.

9. Properly orient and insert the new board and connect

all of the wiring.

10. Reassemble in the reverse order as above.

HEATER ASSEMBLY REPLACEMENT

Tools Required: Phillips Head Screwdriver

Flat Head Screwdriver

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the four screws along the back of the unit,

the two on either side along the top edge and the two

at the top of the glass retaining bracket on both sides.

(Figure 3)

4. Lay the Compact Fireplace on its back.

5. Gently open the top panel, laying it on the work sur-

face so that all of the components can easily be seen.

(Figure 4)

6. Locate the heater assembly and disconnect the wiring

connections noting their original locations.

NOTE: A at head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

7. Remove the 4 screws that secure the top panel to the

heater assembly

8. Properly orient and install the new assembly and con-

nect all of the wiring.

WARNING: Ensure wires do not come in contact with

moving parts by securing wires in wiring tie wraps.

9. Reassemble in the reverse order as above.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Dimplex DF2624L Service Manual Page 8

Comments to this Manuals

Related products and manuals for Fireplaces Dimplex DF2624L