Dimplex DF2624L Service Manual download pdf (Page 10)

10 www.dimplex.com

LED DRIVER BOARD REPLACEMENT

Tools Required: Phillips Head Screwdriver

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the three screws along the back of the unit,

the two that hold the glass retaining bracket on both

sides and the two on either side along the bottom edge.

(Figure 6)

4. Lay the Compact Fireplace on its back.

5. Gently open the bottom panel, laying it on the work sur-

face so that all of the components can easily be seen.

(Figure 8)

6. Locate the LED driver board and disconnect the wiring

connections noting their original locations.

NOTE: A at head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

7. Release the driver board from the top panel by using

needle nose pliers to depress the tab on the mounting

standoffs and gently lift the driver board off.

8. Properly orient and install the new LED driver board

and connect all of the wiring.

9. Reassemble in the reverse order as above.

LED LIGHT ASSEMBLY REPLACEMENT

Tools Required: Phillips Head Screwdriver

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the three screws along the back of the unit,

the two that hold the glass retaining bracket on both

sides and the two on either side along the bottom edge.

(Figure 6)

4. Lay the Compact Fireplace on its back.

5. Gently open the bottom panel, laying it on the work sur-

face so that all of the components can easily be seen.

(Figure 8)

6. Locate the LED lights along the back. Each light is

secured with four screws and there is a light lter that is

sandwiched between the light assembly and the sheet

metal bracket.

NOTE: New light lters are not provided with replace-

ment lights and will need to be reinstalled in the original

locations.

7. Disconnect the wiring connections noting their original

location.

8. Properly orient and install the new LED lights and con-

nect all of the wiring.

9. Reassemble in the reverse order as above.

LOG SET ASSEMBLY REPLACEMENT

Tools Required: Phillips Head Screwdriver

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights, heating elements and top

panel to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. Unplug the unit from power outlet.

2. Remove the rebox from the back of the mantel by

removing the retaining screws which secure the rebox

brackets to the mantel.

3. Remove the two screws on each side of the rebox that

secure the log set to the outside panels.

4. Pull the front edge of the plastic Ember Bed or plastic

grate up and forward until the rear tab releases from

the ledge located at the bottom of the Partially Reect-

ive Panel. (Figure 9)

IMPORTANT: Only handle the Log Set by the Ember

Bed.

NOTE: Log Set ts tightly into rebox, some force may

be necessary to remove.

5. Disconnect the wiring connections noting their original

location.

6. Remove the two screws on each side that secure the

log set support brackets to the rebox remove the par-

tially reective panel by sliding it out of the side chan-

nels towards the bottom. (Figure 9)

7. Reassemble in the reverse order as above.

Side Section

Front

Edge

Log

Ember

Bed

Back

Ledge

Rear

Tab

Figure 7

1 2 ... 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Dimplex DF2624L Service Manual Page 10

Comments to this Manuals

Related products and manuals for Fireplaces Dimplex DF2624L