Dimplex Chesford CSD20 Service Manual download pdf (Page 12)

Mirror Retaining Bracket in place (Figure 7, page 7) and

remove.

9. Slide Mirror up from within the rebox to remove.

10. Remove the Log Set by pulling it straight up and out of

the rebox.

11. Pull the Flicker Rod to the far right, towards the Flicker

Motor, then bend it gently enough to clear the bracket on

the left (Figure 8, page 8).

12. Pull the Flicker Rod carefully away from the Flicker Motor

until cleared.

13. Turn the rebox onto it’s back.

14. On the bottom of the unit, remove: four (4) Phillips

screws along the bottom edge of the rebox (the rebox

Mounting Bracket will separate here as well); two (2)

screws along each side; two (2) screws under the front

edge of the rebox; and one (1) screw which connects to

the Heater Assembly (Figure 10, page 9). The Bottom

Panel can now be removed.

15. Carefully turn rebox right side up and remove the four

(4) Phillips screws from inside the rebox as shown in

Figure 13 (page 10) to release the Heater Assembly.

16. Carefully return the rebox onto it’s back, supporting the

now loose Heater Assembly below.

17. Pull gently on the Heater Assembly in order to angle it

outwards from the rebox and maximize working space

inside the heater compartment.

18. The Remote Receiver Board is mounted to the side

of the rebox (Figure 15) by four (4) Mounting Studs,

located in each corner of the Receiver Board. Remove

each of the three (3) wire clips from the board.

to be inserted through the sheet metal of the chassis

from the outside).

21. Reconnect the three (3) wire clips from step 18 following

Figure 15 as a guide.

22. Follow steps 1 through 17 in reverse order to reassemble

the replace.

Power Cord Replacement

If the replace was operating prior to servicing allow at least

ve (5) minutes for light bulbs and heating element to cool off

to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or

cleaning to reduce the risk of electric shock or damage to

persons.

Replacement Procedure:

1. Pull replace away from the wall far enough to access

the back of the unit.

NOTE: Although it is not necessary to remove the

rebox insert from the mantel, we suggest doing so for

better manageability.

2. Remove two (2) Phillips screws from each of the four (4)

brackets which attach the rebox to the mantel

(Figure 4, page 6).

3. Carefully push rebox out the front of the mantel to

remove (Figure 5, page 6).

4. Gently turn the rebox so that it rests on its front surface.

5. On the Back Panel of the rebox, remove the two (2)

Phillips screws that hold the Power Cord Access Panel in

place (Figure 16).

19. Either squeeze the clasp of each Mounting Stud to

release, or use side cutters to cut and clear them from

both board and chassis (replacement studs will be

included with the replacement part) and remove the

defective Receiver Board.

20. Properly orientate the replacement Receiver Board and

push it onto the four (4) Mounting Studs until snapped

into place (if the studs were cut, replacements will need

Figure 15

Blue wire

Orange

wire

White wire

Remote

Receiver Board

Mounting

Studs (4)

Figure 16

Screws to

remove (2)

Power Cord

Access Panel

6. Gently pull the cord and Access Panel away from the

rebox to allow enough slack in the wires to work.

7. Refer to Figure 17 and using a small, at head

1 2 ... 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Dimplex Chesford CSD20 Service Manual Page 12

Comments to this Manuals

Related products and manuals for Fireplaces Dimplex Chesford CSD20