Dimplex DXC20TI Operations Instructions download pdf (Page 1)

3 No. Wall

Mounting

Brackets

shelf /

ceiling

floor

bracket slot

358mm centres - 2kW

478mm centres - 3kW

518mm Min.

515mm Min.

Dimensions

(millimetres)

Installation and Operating Instructions

Convector Heaters

Models : DXC20, DXC20Ti, DXC30, DXC30Ti and DXC30FTi

INDCUK35RG Issue 0

Models Specification

DXC20 2.0kw Heat Switch/Thermostat/Neon

DXC20Ti 2.0kw Heat Switch/Thermostat/24hr Timer

DXC30 3.0kw Heat Switch/Thermostat/Neon

DXC30Ti 3.0kw Heat Switch/Thermostat/24hr Timer

DXC30FTi 3.0kw Heat Switch/Thermostat/24hr Timer/Turbo Fan

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

WARNING – THIS APPLIANCE MUST NOT BE USED IN A BATHROOM.

WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.

WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY

BELOW A FIXED SOCKET OUTLET.

DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS

ARE FITTED CORRECTLY.

FOLLOW these instructions carefully.

NEVER cover or obstruct in any way the heat outlet slots at

the top of the heater or the air inlet slots in the base of the

heater.

The heater carries a warning ‘DO NOT COVER’ to alert the user

to the risk of fire that exists if the heater is accidentally

covered.

Timer models DXC20Ti, DXC30Ti and DXC30FTi can be set to

switch on automatically. Remember to observe all safety

warnings at all times.

Caution: In order to avoid a hazard due to inadvertent resetting

of the thermal cutout, this appliance must not be supplied

through an external switching device, such as a timer, or

connected to a circuit that is regularly switched on and off by

the utility.

This appliance is not intended for use by children or other

persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they do

not play with the appliance.

If young children, the aged or infirm are likely to be left in the

vicinity of the heater, we advise that adequate precautions

should be taken. We recommend that a guard be fitted to

ensure contact with the heater is avoided and objects cannot

be inserted into the product.

If the mains lead is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified

person in order to avoid a hazard.

For further information, please contact our guard supplier

direct on Tel. No. 01603 667957, or in case of difficulty or for

further advice contact the Customer Helpline.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an ~ supply only and the voltage marked on

the heater must correspond to the supply voltage. This heater is fitted

with a rewireable plug incorporating a 13 amp fuse. In the event of

replacing the fuse in the plug supplied, a 13 amp fuse approved by ASTA

to BS 1362 must be used. If any other type of plug is used, a 15 amp fuse

must be fitted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code :

GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by

the earth symbol , or coloured GREEN or GREEN AND YELLOW.

Connect the BROWN wire to the terminal marked ‘L’ or coloured RED.

Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.

Wall Mounting

Three identical wall mounting brackets are secured to the base of the

heater with a fixing screw. To wall mount appliance, first remove the

brackets as follows :

Lay the heater on its back.

Following the sequence in Fig. 1 – identify and remove the fixing screw

securing the brackets located beside Mains Cable as shown in (a), then

pull out brackets and rotate them to disengage them from the slot (b).

Withdraw the brackets from the slot (c).

Select a suitable position on a wall, near to a mains power socket, making

sure that there is

at least

230 mm below the heater and

at least

450 mm

above the heater of unobstructed space. See also ‘Positioning the heater’.

Fix the two top retaining brackets to the wall, using suitable fixings, for

2kW models at 358mm centres and 3kW models at 478mm centres – see

Fig. 2.

Locate the heater on the top brackets and allow it to hang in place.

Fit the bottom bracket into the slot in the heater and then fix it to the wall.

Test that the heater is now securely fixed to the wall.

(a) (b) (c)

Wall Mounting

Brackets

Fig. 1

Fig. 2

150

418

230

695 - 3.0kW

575 - 2.0kW

MIN

230

450

350

MIN

1 2 3 4

Summary of Contents

Page 1 - Convector Heaters

3 No. WallMountingBracketsshelf / ceilingfloorbracket slot358mm centres - 2kW478mm centres - 3kW518mm Min.515mm Min.Dimensions(millimetres)Installatio

Page 2 - Controls

(b)(a)foot fixingscrewwall mounting bracketsPositioning the heaterAlways ensure that the heater is stood on a firm, level base near to, butnot directl

Page 3 - (DXC30FTi) - see Fig. 10

Switching to autoSet the heat selector and thermostatfor the heat output required.Check that the clock shows thecorrect time of day. Set the I - - sl

Page 4 - [c] Dimplex UK Limited

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)EN55014, EN60555-2